充氣假目標漏氣后可按以下步驟修補：

　　After the inflated false target leaks, it can be repaired according to the following steps:

　　1.查找漏氣點

　　1. Find the leakage point

　　· 將假目標充氣后，用肥皂水涂抹或噴灑在表面，觀察冒泡處即為漏氣點。

　　·After inflating the fake target, apply or spray soapy water on the surface, and observe the bubbling point as the leak point.

　　· 若肥皂水法不便，也可在安靜環境中擠壓假目標，貼近表面傾聽漏氣聲，輔助定位。

　　·If the soap water method is inconvenient, you can also squeeze the fake target in a quiet environment, listen closely to the surface for air leakage sound, and assist in positioning.

　　2.準備修補材料

　　2. Prepare repair materials

　　· 根據假目標材質（如PVC、牛津布等），選擇匹配的補片材料。

　　·Select the matching patch material based on the fake target material (such as PVC, Oxford cloth, etc.).

　　· 準備專用膠水（如帳篷膠水、強力橡膠膠水），確保膠水具有防水性和耐候性。

　　·Prepare specialized glue (such as tent glue, strong rubber glue) to ensure that the glue has waterproof and weather resistance.

　　· 準備剪刀、清潔布、酒精棉片等工具。

　　·Prepare scissors, cleaning cloth, alcohol swabs, and other tools.

　　3.清潔漏氣區域

　　3. Clean the leaking area

　　· 用清潔布蘸取酒精或溫和肥皂水，擦拭漏氣點及周圍，去除灰塵、油污和雜質，確保表面干燥、干凈。

　　·Dip a cleaning cloth in alcohol or mild soapy water, wipe the leak point and its surroundings, remove dust, oil stains, and impurities, and ensure that the surface is dry and clean.

　　4.裁剪補片

　　4. Cutting patches

　　· 根據漏氣孔大小，用剪刀裁剪補片，補片形狀盡量規則，邊緣需超出漏氣孔一定距離（約1-2厘米），以保證粘貼牢固。

　　·According to the size of the leakage hole, cut the patch with scissors. The shape of the patch should be as regular as possible, and the edge should exceed the leakage hole by a certain distance (about 1-2 centimeters) to ensure a firm adhesion.

　　5.涂抹膠水并粘貼補片

　　5. Apply glue and stick patches

　　· 在漏氣處和補片背面均勻涂抹膠水，等待膠水稍干至不粘手狀態（具體時間參考膠水說明）。

　　·Apply glue evenly to the leak and the back of the patch, and wait for the glue to dry slightly until it does not stick to your hands (refer to the glue instructions for specific time).

　　· 將補片對準漏氣點，從一端開始慢慢粘貼，確保補片與假目標表面緊密貼合，無氣泡或褶皺，可用手指或軟布輕輕按壓，擠出多余膠水。

　　·Align the patch with the leak point and slowly stick it from one end, ensuring that the patch is tightly attached to the surface of the fake target without bubbles or wrinkles. Use your fingers or a soft cloth to gently press and squeeze out excess glue.

　　6.固定與固化

　　6. Fixation and solidification

　　· 粘貼后，用重物（如書本、磚塊）壓在補片上，保持壓力2-24小時（具體時間依膠水要求），確保補片牢固粘合。

　　·After pasting, press a heavy object (such as a book or brick) onto the patch and maintain the pressure for 2-24 hours (the specific time depends on the adhesive requirements) to ensure that the patch is firmly bonded.

　　· 固化期間避免觸碰補片，待膠水完全干燥后，方可充氣測試。注意事項：

　　·During the curing process, avoid touching the patch and wait for the adhesive to completely dry before conducting the inflation test. Notes:

　　· 若漏氣孔較大或補片無法完全覆蓋，可分層修補或聯系廠家返廠維修。

　　·If the leakage hole is large or the patch cannot fully cover it, it can be repaired layer by layer or the manufacturer can be contacted for return to the factory for repair.

　　· 補修后需進行充氣測試，觀察是否仍有漏氣，確保修補效果。

　　·After repair, it is necessary to conduct an inflation test to observe whether there is still air leakage and ensure the repair effect.

　　· 日常使用中注意避免尖銳物體劃傷假目標，存放時保持干燥、通風，避免高溫或陽光直射。

　　·Be careful to avoid scratching false targets with sharp objects during daily use. Keep them dry and ventilated during storage, and avoid high temperatures or direct sunlight.

　　本文由  充氣假目標 友情奉獻.更多有關的知識請點擊  http://m.yowp.cn/  真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is contributed by the inflatable fake target friendship For more related knowledge, please click http://m.yowp.cn/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.